Garden Gates, Driveway Gates, Wood Fences, Garden Arbors, Porch swings by Prowell Woodworks Garden Gate Products Gate Hardware Contact Prowell Woodworks About Charles Prowell Woodworks Payment Gateway Site Map

prowell woodworks for garden gates
  

 

Open Style Double Driveway Gates Grids Openings at Approximately 5"

>>How to Order
 

 

DRIVEWAY ENTRANCE GATES #13
This Driveway Gate Style is Base Price + 18%
Follow the link to the Base Price Table
 


    DRIVEWAY GATE #13-1
       
An equal number of full grids horizontally within the fixed width at 5.11" square per grid. To create an equal number of full grids vertically becomes more difficult. Here we were able to increase the width of the bottom rail to 11-1/2", up from the normal 8-1/2". The homeowner preferred this over the aesthetics of a row of partial grids along the bottom.
 
 
 
open grid wood driveway gate
 
 
 


Driveway Gates #13 nestled in the rolling hills of west Marin County, California--flanked by matching gate and panel. Surface-mounted to a steel frame exposed on the property side and automated with above-grade motors.
  driveway gate open grid design
 
 
 


CPW and the homeowners are currently considering designs for two wood lighting fixtures to seat themselves on top of the columns.
  wood driveway gates opening to 90 degrees
 
 
  And finally, in keeping with a tradition that began ages ago, we post a photo of the resident munchkin.
  country property wood driveway gates in Marin County, CA
 
 
 
    DRIVEWAY GATE #13-3
      Grid Openings: 4.27"W x 5.09" H

Open flush-Joined grids that are slightly irregular, with the width being almost 1/4" more than the height. This also helped to provide equal grids vertically and horizontally across the gates. We also added to the normal width of the bottom rail, bringing it to 10".

Many communities, such as Kent-Woodlands in Marin County, CA, require that a certain percentage of the Driveway Gate is open, with a smaller percentage as solid. This is obviously to prevent a neighborhood with barrier-like gates fronting the properties.
  Driveway Gate
 
 
 

There is a decided difference between grids that overlap, such as lattice, and grids that are joined flush.

Note: What we have here is an example of of successive layers of finish applied with the best of intentions. Read the labels: Most stains and pigmented finishes seal on the first coat and any additional coats simply lay on the surface and result in a splotchy finish.
  Electric Gate
 
 
 
As an Automatic Gate, showing the sub-Grade SEA motors. Mounted to pins that pivot, with the top and bottom pins perfectly aligned. The motor is under the steel plate on the bottom. More information on this type of automation motor can be found on the Specifications page. If you or your installer opt for the in-ground motor, CPW will call out the clearance and provide the plates top and bottom mortised into the gate.
  Automatic Gate   Electric Gate
 
 
 

The matching Pedestrian Gate style #60-1

An equal number of square grids horizontally is easily calculated within a fixed width. Vertically, however, and we are almost always left with the choice of either a partial grid at the bottom, or an extended grid height, or a bottom rail with an increased width. Here our bottom row of grids are the same size as the others by increasing the width of the bottom rail. But beware, in that this is not always possible and depends largely on the size of the remainder grid.

Price Link: Base + 11%
  garden gates in Marin county, CA


>>>To GALLERY 2
driveway gates
>>>To DRIVE GATE PRICE TABLE
The Designs of Prowell Woodworks are protected by Patents and Patents Pending.
 



1. 8 0 0 . 4 6 6 . 1 8 5 0
1 .7 0 7 . 8 2 3 . 3 7 1 1 (PST)
1 . 7 0 7 . 8 6 1 . 3 4 0 9 (FAX)

 

SHIPPING TO ALL 50 STATES
©1996-Present Charles Prowell.
The CPW Web Site was launched in 1996.
Products appearing on this site are the sole design rights of   Charles & Ben Prowell.

Privacy

 

 

#13--0761-Grimshaw
#13-1 (1108-Tsao